移动工具箱:请帮忙翻译一下

最高水平定时器是延迟时间在最大平实传感器的.position 和哺养的设备的再开始之间为装货跳跃者。
滴下饲料删去时间当植物从主要速度搬走向一滴阶段, 读书必须失去能力避免消极影响由高流程的振动造成, 为这转换的时期从扼要和一滴饲料的, 重量不被检查。
另外卸载时间当桶开放释放产品被药量入它, 它停留开放直到重量在它下降在10% 最后重量以下被记录。 一旦它是在这重量之下另外的放电时间开始, 仍然允许产品在桶对流程。
增加的auto?zero 延迟在调零之前系统被停下来允许所有振动被吸收在时刻由这个参量设置。
另外的读书延迟一旦药量一滴饲料鼓被完成了并且在读书被采取之前, 那个单位必须等所有产品在空气分成鼓, 一旦重量是稳定的机器等这时间在读完成的重量之前。
自动零频率被使用对集合频率为自动调零, 如果你编程3 分钟例如, 单位将调零自己每3 分钟, 如果自动调零被编程作为零, 单位调零自己在各个周期的结束, 可能被设置的最大时刻是9 分钟, 依从R61 公尺type-approval 单位并且调零自己每次它改变结束中止和开始。

原文
Max level off timer—is the delay time between the off position of the max level sensor and the restart of the feeding device for the loading hopper.
Dribble feed blanking time—when the plant moves on from the main speed to the dribble phase, the readings must be disabled to avoid negative affects caused by the vibrations of the high flow, for this time of changeover from main and dribble feeds, the weight is not checked.
Additional unload time—when the bucket open to discharge the product dosed into it, it stays open until the weight in it drops below 10% of the last weight recorded. once it is below this weight the additional discharge time starts, to allow the product still in the bucket to flow out.
Added auto－zero delay—before zeroing itself the system is stopped to allow all vibrations to be absorbed for the time set by this parameter.
Additional reading delay—once dosing of the dribble feed drum has been completed and before the reading are taken, that unit has to wait for all the product in the air to fall into the drum, once the weight is stable the machine waits for this time before reading the finished weight.
Auto-zero frequency—used to set the frequency for auto-zeroing, if one programmes 3 minutes for example, the unit will zero itself every 3 minutes, if auto-zeroing is programmed as zero, the unit zeroes itself at the end of each cycle, the maximum time that can be set is 9 minutes, in compliance with the R61 metric type approval the unit also zeroes itself each time it changes over STOP and START.
翻译文
离开定时器的最大水平-是在最大同高的感应器的远位置之间计时的延迟和那为载入漏斗逐渐强烈装置重新开始。
流口水饲养遮没时间-当植物继续的时候从主要的速度到那流口水状态, 阅读一定被无效避免由高的流程的震动所引起的否定的情绪, 为来自主要部份的转换的这次而且流口水饲养, 重量没被检查。
另外的卸载时间-桶子何时打开放电进入它之内被配的产品, 它在它里面在被记录的 10% 的最后重量下面停留开着直到重量下降。 一经它在这重量下面另外的解除时间开始, 在桶子中仍然允许产品流动出。
附加的汽车－零延迟-在对准零位它本身系统之前被停止让所有的震动对于被这一个叁数设定的时间被吸收。
另外的阅读延迟-一次配那流口水饲养鼓已经被完成而且在阅读之前被采取,那一个单位必须等候在空气中的所有产品掉入鼓, 一经重量是赶入马房里机器在读完成的重量之前等候这次。
汽车-零的频率-过去一直为汽车设定频率-对准零位, 如果一举例来说为 3 分钟规划程序,单位每 3 分钟将会对准零位它本身, 如果对准零位汽车的被规划如零, 单位在每个周期结束的时候对准零位它本身,可能是组的最大的时间是 9 分钟, 在符合 R61 的作法公制的类型赞成单位也每次对准零位它本身它变更停止而且开始。

Max level off timer—is the delay time between the off position of the max level sensor and the restart of the feeding device for the loading hopper.
走开同高定时器—的最大为载入漏斗是在最大同高的感应器的远位置和逐渐强烈的装置重始之间延迟时间。

Dribble feed blanking time—when the plant moves on from the main speed to the dribble phase, the readings must be disabled to avoid negative affects caused by the vibrations of the high flow, for this time of changeover from main and dribble feeds, the weight is not checked.
流口水饲养使空白时间—当植物继续行进的时候从主要的速度到那流口水时期, 阅读一定被无效避免否定藉着高的流程震动影响引起, 为这次转换从主要部份而且流口水饲养,重量不被检查。

Additional unload time—when the bucket open to discharge the product dosed into it, it stays open until the weight in it drops below 10% of the last weight recorded.
附加的卸载时间—当桶子打开放电进入它之内被配的产品时候,它在被记录的 10% 的最后重量下面停留开着直到重量在它里面降低。

once it is below this weight the additional discharge time starts, to allow the product still in the bucket to flow out.
一经它是在这重量附加的解除时间开始下面, 在桶子中仍然允许产品流动出。

Added auto－zero delay—before zeroing itself the system is stopped to allow all vibrations to be absorbed for the time set by this parameter.
附加的汽车－零延迟—在对准零位它本身系统之前被开始允许所有的震动被这一个叁数为时间被吸收组合。

Additional reading delay—once dosing of the dribble feed drum has been completed and before the reading are taken, that unit has to wait for all the product in the air to fall into the drum, once the weight is stable the machine waits for this time before reading the finished weight.
附加的阅读延迟—一次配那流口水饲养鼓已经被完成和在阅读之前被拿, 那一个单位必须等候空气的所有产品掉入鼓, 一次重量是赶入马房里机器这次在读完成的重量之前等候。

Auto-zero frequency—used to set the frequency for auto-zeroing, if one programmes 3 minutes for example, the unit will zero itself every 3 minutes, if auto-zeroing is programmed as zero, the unit zeroes itself at the end of each cycle, the maximum time that can be set is 9 minutes, in compliance with the R61 metric type approval the unit also zeroes itself each time it changes over STOP and START.

汽车- 零频率—过去一直设定频率为对准零位汽车的,如果一举例来说为 3 分钟规划程序,单位每 3 分钟将会对准零位它本身, 如果对准零位汽车的被规划如零, 单位在每个周期结束的时候对准零位它本身, 可能是的最大时间放置是 9 分钟, 在符合 R61 的作法公制的类型赞成单位中也每一次对准零位它本身它变更停止和开始。